disable theeft lock - Chevy Malibu Forum: Chevrolet Malibu Forums
 
LinkBack Thread Tools Display Modes
post #1 of 5 (permalink) Old 02-16-2009, 07:36 AM Thread Starter
CMF Rookie Member
 
Join Date: Feb 2009
Location: mexico
Posts: 4
Send a message via MSN to henrybu01
disable theeft lock

i have a 2001 malibu but i don`t have the remote control for locks and alarm and the theeft lock engaged how can i disable it my car doesn`t starts

any one help me
henrybu01 is offline  
Sponsored Links
Advertisement
 
post #2 of 5 (permalink) Old 02-17-2009, 10:37 PM
CMF Junior Member
 
jester's Avatar
 
Join Date: Sep 2008
Location: Wenatchee, WA
Posts: 59
Re: disable theeft lock

Turn ON the ignition, not START.

Walk away for at least 10 minutes... seriously

Turn off and then it should start like normal. This is the GM Passlock security sysytem.
jester is offline  
post #3 of 5 (permalink) Old 02-18-2009, 05:25 PM
CMF Senior Member
 
BillD64's Avatar
 
Join Date: Aug 2008
Location: Endicott, NY
Posts: 473
Re: disable theeft lock

Here is the Service Manual procedure for relearning the PassLock:

Programming Theft Deterrent System Components
Programming Replacement Passlock™ Sensor, BCM, or PCM

Important
Due to component variability, the vehicle theft deterrent (VTD) system must have the learn procedure performed regardless, if the vehicle starts on the first ignition cycle after a VTD repair.

All codes in the theft deterrent module must be cleared for a relearn.



Important
The body control module (BCM) must be programmed with the proper RPO configurations before performing learn procedures. Refer to Body Control Module (BCM) Programming/RPO Configuration in Body Control System.
If replacing the BCM with a GM Service Parts Operations (SPO) replacement part, the module will learn passlock™ sensor data code immediately. The existing PCM however, must learn the new fuel continue password when the BCM is replaced.
If replacing a PCM with a GM Service Parts Operations (SPO) replacement part, after programming, these modules will learn the incoming fuel continue password immediately upon receipt of a password message. Once a password message is received, and a password is learned, a learn procedure must be performed to change this password again. A PCM which has been previously installed in another vehicle will have learned the other vehicle's fuel continue password and will require a learn procedure after programming to learn the current vehicle's password.

Conditions
Use this procedure after replacing any of the following:

Passlock™ Sensor
BCM
PCM
10 Minute Learn Procedure
1. Turn ON the ignition, with the engine OFF.
2. Attempt to start the engine, then release the key to ON, vehicle will not start.
3. Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.
4. Turn OFF the ignition, and wait 5 seconds.
5. The vehicle is now ready to relearn the Passlock™ Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.

Important
The vehicle learns the Passlock™ Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.


6. Start the engine, the vehicle has now learned the Passlock™ Sensor Data Code and/or password.
7. With a scan tool, clear any DTCs if needed, history DTCs will self clear after 100 ignition cycles.


Bill
BillD64 is offline  
post #4 of 5 (permalink) Old 02-23-2009, 09:49 AM Thread Starter
CMF Rookie Member
 
Join Date: Feb 2009
Location: mexico
Posts: 4
Send a message via MSN to henrybu01
Re: disable theeft lock

thanks you all for your answers i did the 10 min and it works fine the greenhornet is allready on the road

see you all around

thanks again
henrybu01 is offline  
post #5 of 5 (permalink) Old 03-23-2009, 09:18 PM
CMF Senior Member
 
green03malibu's Avatar
 
Join Date: Jan 2009
Location: Salisbury, MD
Posts: 184
Re: disable theeft lock

i remember that happened me once, i barely went threw a puddle of water and it did it.
green03malibu is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Chevy Malibu Forum: Chevrolet Malibu Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
Disable auto locking doors? 2001FZ1 General Discussion (Generation 7) 17 01-03-2010 07:53 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome