Sounds like a ricer question I know, but take a look and you'll know why I wanna get one...
http://i242.photobucket.com/albums/ff169/thelongone13/P1040111.jpg
It's not for performance, her 06 has a small gas tank and could use a boost in range. Any ideas where I can get an intake for this thing?

you can make your own if you are skilled enough. a Cold air intake is easilly reproduced at a fraction of the cost of buying one from a "dealer"

Here is what your looking at, you already have a plastic intake which is far ahead of the chrome ones which are horrible for your engine, but make it look nice. You can re-route the intake to a shorter pull, but taking in air through your bumber grills, into a filter in a box (ask later) and the up to the throttle body and in.
it would make you intake half the length and get colder air to the engine which would increase fuel efficiency.

i pulled the whole intake and fabbed up a custom 1 using parts from auto zone.all parts r installed after the MAP sensor and i also pulled the air box but you need 2 remove the inner fender trim panel 2 get 2 it ill post pics in a couple days let me know how it goes!

I have a kit similar to what you guys are talking about on my Grand Prix. I would love to make one, but I don't know where I would even route it... There isn't much space on the driver's side like the GP. This is kinda what I was hoping to do, but I lack the knowledge of where to put it.
http://i242.photobucket.com/albums/ff169/thelongone13/04-08-08_2035.jpg
This is the kit (assembled for photo)
http://i242.photobucket.com/albums/ff169/thelongone13/04-08-08_1648.jpg

Just follow the stock tubing,remove the air cleaner box,purchase the K&N filter element with the adapter 3" and attach AFTER the MAP sensor

I may have to try that. The tubing is rigid after all.

Alot of people put chrome intakes on their car, that makes their car a nice "hot air intake" system.

you can also be creative and route the intake into the right fender where the stock air box is located and pull off that stock-aftermarket look.As soon as i find my camera i will post pictures for you to reference!

www.mpracing.org sells a fenderwell intake for your year malibu.

sweet intake and the best part about that product is it runs into the fender AWAY from the motor and all that HOT air im gonna remove my setup and order 1 for myself thanx

No problem, glad to help out.

you can make your own by getting some 90 degree pvc and some sewer couplings for $10

OK, update: I've decided to use the same K&N 9" cone filter as the one on my car at the end of the MAF in hopes of better mileage. This is, after all, a trip car and could use a little better range/economy. I have another question, but that's for another thread... :D Thanks all!

I heard from many people that PVC is not the best option for intakes. When PVC gets hot it emits gases that are not good for the engine.

What?!?!? PVC Does not get hot in the engine bay as it is not a heat conductor. Maybe if you had an engine fire, then it would be bad for your engine.

Hear is a intake for the 08-09 Malibu 2.4L: http://cgi.ebay.com/ebaymotors/08-09-Chevy-Malibu-2-4-Ecotec-Stg-3-AIR-INTAKE-K-N_W0QQcmdZViewItemQQcategoryZ38634QQihZ016QQitemZ2 60290105962QQrdZ1QQsspagenameZWDVW

It is chrome plated and not dipped, therefore it will eventually flake off and try to get into your engine, plus it is chrome...bad choice for intake for performance. Chrome is only a good visual mod.

Yeah, I tried fitting up my filter and it will fit. I'm ordering a new one once I have the money. For those with the 04-07 Malibu V6, the K&N P/N is RE-0870. Also need a coupler from 3" (intake tube) to 4" (filter opening).